Axiohm A794-D100 Instrukcja Obsługi Strona 18
- Strona / 147
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
A794 Owner’s Guide Chapter 2: Using the Printer
December 1999 13
Loading Receipt Paper
Change the paper when any of the following conditions occurs:
♦
Colored stripe appears on the receipt paper indicating the paper is low.
Change the paper as soon as possible to avoid running out of paper part way
through a transaction.
♦
Green LED flashes (slow flash) indicating the paper is low.
Change the paper as soon as possible to avoid running out of paper part way
through a transaction.
♦
Green LED flashes (quick flash) indicating the paper is out.
Change the paper immediately or data may be lost.
Caution: Do not operate the printer or host computer if the printer runs out of paper.
The printer will not operate without paper, but it may continue to accept data
from the host computer. Because the printer cannot print that additional data,
it may be lost.
To Load the Paper:
1.
Open the Rear Cover by lifting up on each side of the cover until it unsnaps.
- Owner's Guide 1
- Legal Notices 2
- December 1999ii 3
- Contents 4
- Chapter 1: About the Printer 6
- Description of Printer 7
- Models Available 8
- Features 9
- Chapter 2: Using the Printer 10
- Unpack the Printer 11
- Choose a Location 13
- Connect the Cables 14
- Cash Drawer Cables 15
- Power Supply Cable 15
- Printer Controls 16
- Loading Receipt Paper 18
- Configuring the Printer 21
- December 1999 17 22
- Troubleshooting the Printer 23
- Printing Problems 24
- Printer Does Not Function 24
- December 199920 25
- Ordering Thermal Paper 26
- Ordering Cash Drawers 28
- Ordering Communication Cables 29
- Wall-Mount Kit 29
- Characters 31
- Paper Specifications 32
- Print Zones 32
- Print Zones for 82.5 mm Paper 34
- Character Sets 37
- Code Page 850 38
- Code Page 852 39
- Code Page 858 40
- Code Page 860 41
- Code Page 863 42
- Code Page 865 43
- Code Page 866 44
- Code Page 1252 45
- Communication Overview 47
- RS-232C Interface 48
- XON/XOFF Protocol 49
- DTR/DSR Protocol 50
- Power Connector 51
- Cash Drawer Connector 51
- RS-232C Settings 52
- Parallel Interface 53
- Command Conventions 55
- List of Commands and Location 56
- By Function 60
- Print Characteristic Commands 61
- Graphics Commands 62
- Barcode Commands 63
- Comparisons 65
- Command Descriptions 66
- Perform Partial Knife Cut 67
- Generate Tone 67
- Initialize Printer 68
- Bit Sensor 0 1 70
- Sensor Status 70
- Select Cut Mode and Cut Paper 71
- Print Test Form 72
- Print and Feed One Line 73
- Activate Carriage Return 73
- Print Lines 73
- Dot Rows 74
- Extra Dot Rows 74
- Set Line Spacing to 1/6 Inch 75
- Set Line Spacing 75
- Print and Feed Paper 76
- Print and Feed 76
- Horizontal Tab 77
- Set Column 77
- Set Horizontal Tab Positions 79
- Set Relative Print Position 80
- Select Justification 81
- Set Left Margin 82
- Set Printing Area Width 83
- Select Double-Wide Characters 84
- Select Single-Wide Characters 84
- Select Pitch (Column Width) 85
- Select Print Mode 87
- Cancel User-Defined Character 90
- Select or Cancel Italic Print 92
- Select Character Size 93
- Character Width Selection 94
- Hex Decimal Width 94
- Character Height Selection 94
- Hex Decimal Height 94
- Summary of Rotated Printing 96
- Download BMP Logo 98
- Select Bit Image Mode 99
- December 1999 95 100
- Related Information 100
- Select the Current Logo 103
- Define Downloaded Bit Image 104
- Print Downloaded Bit Image 105
- Status Commands 106
- Value of 107
- Function Description 107
- Bit 0 Bit 1 107
- Status Byte 108
- (RS-232) 108
- Type ID ( 109
- ASCII Hex Dec 110
- Real Time Commands 115
- Auto Status Back 122
- Bar Code Commands 126
- Print Bar Code 127
- Select Bar Code Width 128
- Page Mode Commands 129
- Print Data in Page Mode 130
- Select Page Mode 130
- Select Standard Mode 131
- (x0, y0) 132
- (x0 + dx, y0 + dy) 132
- Print Area 132
- Macro Commands 135
- Execute Macro 136
- User Data Storage Commands 137
- Erase User Flash Sector 139
- Flash Download Commands 140
- Get Firmware CRC 141
- Return Microprocessor CRC 142
- Return Main Program Flash CRC 142
- Erase Selected Flash Sector 142
- Reset Firmware 143
- A794 Owner’s Guide Index 144
- December 1999 139 144
- Index A794 Owner’s Guide 145
- December 1999140 145
- December 1999 141 146
- © 1999 AXIOHM 147
- Printed in U.S.A 147
Powiązane produkty i podręczniki dla Drukuj i skanuj Axiohm A794-D100
Drukuj i skanuj Axiohm 7156 Dokumentacja
(190 strony)
(190 strony)
Drukuj i skanuj Axiohm 7193 Dokumentacja
(85 strony)
(85 strony)
Drukuj i skanuj Axiohm A795 Podręcznik Użytkownika
(128 strony)
(128 strony)
Drukuj i skanuj Axiohm A758 Instrukcja Obsługi
(217 strony)
(217 strony)
Drukuj i skanuj Axiohm 7156 Dokumentacja
(36 strony)
(36 strony)
Drukuj i skanuj Axiohm Astrium Dokumentacja
(14 strony)
(14 strony)
Drukuj i skanuj Axiohm 7193 Dokumentacja
(84 strony)
(84 strony)
Drukuj i skanuj Axiohm 7193 Dokumentacja
(104 strony)
(104 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji